New Products

- Output: 2.7 ton - Jaw Opening: 3.3" - Cut anything from guy wire to anchor rod and most overhead and underground cables - Portable, light weigh...

- Output: 7.8 ton - Jaw Opening: .9" - Specially engineered to cut the toughest EHS guy wire, ground and anchor rods - The anvil style, center cu...

- Output: 19.8 ton - Jaw Opening: 1.25" - Specially engineered to cut the toughest EHS guy wire, ground and anchor rods - The anvil style, center...

- HIGH TENSILE STEEL BOLT CUTTERS WITH INSULATED FIBERGLASS HANDLES - Suitable for cutting hard material - Short cutting edge for high tensile stee...

- HIGH TENSILE STEEL BOLT CUTTERS WITH INSULATED FIBERGLASS HANDLES - Suitable for cutting hard material - Short cutting edge for high tensile st...

- HIGH TENSILE STEEL BOLT CUTTERS WITH INSULATED FIBERGLASS HANDLES - Suitable for cutting hard material - Short cutting edge for high tensile st...

- HIGH TENSILE STEEL BOLT CUTTERS WITH INSULATED FIBERGLASS HANDLES - Suitable for cutting hard material - Short cutting edge for high tensile st...

- High leverage ratcheting mechanism for easy cutting. - Cutting inserts are easily replaced by simply removing 3 screws per blade. - Plastic cov...

  - One handed operation - Compact handle lock for carrying in belt or pouch - A variable force tool by allowing handles to open fully or less than...

- One or two hand operation Compact Ratchet Drive Cutting tool fits in belt or pouch - Used for cutting copper and aluminum cables up to 600 MCM ...

- High-leverage cable cutter - Capacity: 4/O Aluminum                  2/O Copper - Overall Length: 9-1/2" - Handles: Red 

- Streamlights Septor LED Headlamp features seven super bright LEDs that can be toggled into one of three lighting modes. - Its 90 degree tilting h...

- Identical faces with 1-3/4" round-crown driving surface and beveled edges. - Forged, tempered-steel head is only 3-3/4" long for use in tight are...

Features: Linemen's Milled-Face Hammer with one milled face for driving staples used in pole-line work and common, unhardened nails. Other face is...

  - The solution to Midspan Nightmares - For use on twisted wire secondaries up to 600VAC - Used when installing Midspan tap in triplex cable - No...

The OX BLOCK™ is a rope snatchblock with an integrated friction bar used for: Hurtman/self-rescue Lowering Raising Snubbing loads. It allows the...

- High leverage side-cutting pliers. - Cuts ACSR, Screws, Nails and most hardened wire. - Streamlined design with sure gripping, cross-hatched kn...

- High leverage side-cutting pliers - Linemens Bolt Thread Holding Hinge opening holds and cleans 5/8" pole line and hardware bolts or threaded rod...

- High leverage side-cutting pliers - Linemens Bolt Thread Holding Hinge opening holds and cleans 5/8" pole line and hardware bolts or threaded r...

- High leverage side-cutting pliers - Linemens Bolt Thread Holding Hinge opening holds and cleans 5/8" pole line and hardware bolts or threaded r...

- Secure tongue and groove design for non-slip grip, even with heavy presure. - Quick adjust rivet allows one-handed fast, easy adjustment. - Wide ...

- Black markings on yellow, with red stud center markings. - Constructed of tough nylon, reinforced with glass fibers for added durability, and r...

- Shank Length: 6" - Shank Tip Width: 5/16" - Heavy-duty square shank for wrench-assisted turning. - Bolster reinforces shank for hard use. - Des...

- Shank Length: 8" - Shank Tip Width: 3/8" - Heavy-duty square shank for wrench-assisted turning. - Bolster reinforces shank for hard use. - Design...